phase control module atd250hvi repetitive voltage up to 4500 v mean forward current 259 a surge current 5,9 ka final specification apr 17 - issue : 02 symbol characteristic conditions tj [c] value unit blocking v rrm repetitive peak reverse/off-state voltage 125 4500 v v rsm non-repetitive peak reverse voltage 125 4600 v i rrm/drm repetitive peak reverse/off-state current 125 75 ma conducting i t (av) mean forward current 180 sin, 50 hz, th=85c, double side cooled 259 a i t (av) mean forward current 180 sin, 50 hz, tc=55c, double side cooled 383 a i tsm surge forward current sine wave, 10 ms 125 5,9 ka i2 t i2 t without reverse voltage 174 x 10 3 a2s v t on-state voltage on-state current = 1600 a 25 3,34 v v t(to) threshold voltage 125 1,35 v r t on-state slope resistance 125 1,335 mohm switching di/dt critical rate of rise of on-state current, min. from 75% vdrm up to 1050 a; gate 10v, 5 w 125 200 a/s dv/dt critical rate of rise of off-state voltage, min. linear ramp up to 70% of vdrm 125 500 v/s t d gate controlled delay time, typical vd=100v; gate source 25v, 10 w , tr=.5 s 25 1,6 s t q circuit commutated turn-off time, typical dv/dt = 20 v/s linear up to 75% vdrm 320 s q rr reverse recovery charge di/dt = -20 a/s, i= 700 a 125 c i rr peak reverse recovery current vr= 50 v a i h holding current, typical vd=5v, gate open circuit 25 300 ma i l latching current, typical vd=5v, tp=30s 25 700 ma gate v gt gate trigger voltage vd=5v 25 3,50 v i gt gate trigger current vd=5v 25 200 ma v gd non-trigger gate voltage, min. vd=vdrm 125 0,25 v v fgm peak gate voltage (forward) 30 v i fgm peak gate current 10 a v rgm peak gate voltage (reverse) 5 v p gm peak gate power dissipation pulse width 100 s 150 w p g average gate power dissipation 2 w mounting r th(j-h) thermal impedance, dc junction to case, per element 70,0 c/kw r th(c-h) thermal impedance case to heatsink, per element 20,0 c/kw t j operating junction temperature -30 / 125 c v ins rms insulation voltage 50 hz , circuit to base, all terminal shorted 25 6000 v t mounting torque case to heatsink 4 to 6 kn t mounting torque busbars to terminal 12 to 18 kn mass 1500 g ordering information : atd250hvi s 45 standard specification vrrm/100 poseico spa via pillea 42 - 44, 16153 genova - italy tel. + 39 010 8599400 - fax + 39 010 8682006 sales office: tel. + 39 010 8599400 - sales@poseico.com
atd250hvi phase control module final specification apr 17 - issue : 02 dissipation characteristics square wave dc 180 120 90 60 30 80 85 90 95 100 105 110 115 120 125 130 0 50 100 150 200 250 300 350 tcase [ c] i f(av) [a] dc 180 120 90 60 30 0 100 200 300 400 500 600 0 50 100 150 200 250 300 350 p f(av) [w] i f(av) [a]
atd250hvi phase control module final specification apr 17 - issue : 02 dissipation characteristics sine wave 180 120 90 60 30 80 85 90 95 100 105 110 115 120 125 130 0 50 100 150 200 250 300 tcase [ c] i f(av) [a] 180 120 90 60 30 0 100 200 300 400 500 600 0 50 100 150 200 250 300 p f(av) [w] i f(av) [a]
atd250hvi phase control module final specification apr 17 - issue : 02 distributed by 0 100 200 300 400 500 600 700 800 900 0 1 2 3 on - state current [a] on - state voltage [v] on - state characteristic tj = 125 c 0 10 20 30 40 50 60 70 80 0,001 0,01 0,1 1 10 100 zth j - h [ c/kw] t[s] transient thermal impedance 0 1 2 3 4 5 6 7 1 10 100 itsm [ka] n cycles surge characteristic tj = 125 c all the characteristics given in this data sheet are guaranteed only with uniform clamping force, cleaned and lubricated heatsink, surfaces with flatness < . 03 mm and roughness < 2 m . in the interest of product improvement poseico spa reserves the right to change any data given in this data sheet at any time without previous notice . if not stated otherwise the maximum value of ratings (simbols over shaded background) and characteristics is reported .
|
